Windshield Cowling Retainers
These retainers are made from 6061 aluminum, machined and anodized in house. Include stainless steel fasteners. Replace the often broken stock parts.
Made to order, these bars create much needed front structural strength by tying in the door hinge mounts to the inner fender. Hardware included. Each kit comes with 2 complete bars with weld-on or bolt in fender plates. Available for many models, each set is model specific.
Three Point Stainless Strut Bar
These bars are made from Stainless Tubing and Plate, Tig Welded in house using the original chassis for a JIG. Utilizing a three point strut, two on the strut towers, and one against the firewall, creates a very rigid mount which helps prevent body roll and chassis flex. Bars are also available in different colours by choice. Please select platform. For unique intake or engine set ups, please contact firstname.lastname@example.org and we will modify to suit.
Made from Delrin for smoother, tighter shifts.
Comes with 7 bushings, 3 new bolts/nuts, and a new linkage washer. The bushings replace the U-joint linkage bushings, the shifter bottom bushings, and transmission stabilizer linkage bushings. Eliminates the play and slop of stock bushings.
These bushings replace the stock bushings with Delrin machined bushings to eliminate slop and wiggle in the clutch and brake pedals. This wiggle causes premature failure of the clutch retainer, breaking the welds.
Each kit contains 2 bushings.
Standard / Manual Transmissions requires 2 kits.
Automatic Transmissions require 1 kit.
ZC/D16a1 Intake Adapter
Convert your stock d16a1/ZC intake into a newer style D series intake using this Billet 6061 Aerospace Grade adapter. It has a large .750" width for better 3D blending between port sizes. The part comes ready to install, including all hardware. Will allow for D series superchargers, aftermarket intakes, ITBS ect. This plate will open up your D16/zc to a whole new level of aftermarket parts from Skunk, Eagle, AEM ect. Point drilled and marked for NOS ports.
Chisel Head Signature Series Shift Knob
6061 Aluminum, turned and milled in house, these shift knobs give your car a race feel with a tall, smooth grip. Adding weight above the pivot on a shifter helps improve shifting. These signature series are draft cut, for a unique chisel head only found at Cheddas Auto. Available in multiple colors and will fit almost all Acura and Honda Manual Transmissions. Install takes less than 5 minutes.
This shifter is designed to have a fully adjustable handle for best feel while still having the same single bend feel of the stock shifter. adjust handle height and position in seconds. Fully adjustable throw makes for a short shift. Billet 6061 aluminim and stainless construction. Free shift knob included for a limited time.
Dual Bend Billet Fully Adjustable Short Shifter
These short shifters incorporate a billet center and stainless rods, with a double fastened clamp on either end to allow for a fully adjustable height and throw. Not only can you adjust the throw via the threaded linkages, you can also adjust height and position with a simple allen key from inside the car. This is the ultimate short shifter for your 83 - 00 Honda. Available in silver and black. (other colours available upon request). Will fit any standard Honda/Acura knob. Add a Cheddas Auto shift knob for best results.
Single Bend Adjustable Short Shifters
These short shifters are made of Stainless Steel, designed to shorten the throw in your Honda or Acura. Fully adjustable bottom and Delrin Bushings for an ultra smooth tight feel. Adjust from short to wrist flick shifts in less than 10 minutes. Machined to match stock shift knobs, match with a Cheddas Auto Billet knob for best fit.
These shifters are intended to reposition the handle near the steering wheel for a No Reach shift. This allows the driver to keep his hands closest to the steering wheel while racings to help control the vehichle through cornering, traction or loss of traction, and torque steer. Made of stainless alloy and chrome moly components. Delrin bushing bottom end. Fully adjustable throw and position.
Machined from Billet 6061, anodized then engraved with either your choice of the Cheddas Auto "CA" logo or the RPR "Three Flags" logo. Comes in optional colors. Shipments to be made approx mid September. Featuring a MR5 styling, 5 sided, matching bolt pattern of the original MR5 Wheel.